What are the main features of the sewage submersible pump?

Classification:

Sewage submersible pump, also known as submersible sewage pump, sewage submersible sewage pump, mainly used in municipal engineering, hospitals, construction, hotels, restaurants and other industries. It is used to transport wastewater containing solid particles and various long fibers, urban domestic sewage and rainwater, as well as raw water transportation, aquaculture, irrigation, etc.

　　Submersible electric sewage pumpAlso known as submersible sewage pump, sewage submersible sewage pump, mainly used in municipal engineering, hospitals, construction, hotels, restaurants and other industries. It is used to transport wastewater containing solid particles and various long fibers, urban domestic sewage and rainwater, as well as raw water transportation, aquaculture, irrigation, etc. If equipped with special materials, can also be used for some corrosive media occasions. The temperature of the medium should not exceed 40. The pH range is 4-10. In principle, the relative density of the medium should not exceed 1.1. Three-phase 380V,50Hz power supply is adopted. Generally, the diving depth is less than 10m, and the water level can be automatically controlled according to user requirements [7-8].

污水污物潜水电泵

　　Submersible electric sewage pumpThe features are as follows:

1) The stator and rotor of the submersible motor shall be of ordinary Y-type and Y-type, and the power cable control cable detection device shall be used. Stator rotor housing bearing and oil chamber volute impeller wear ring mechanical seal.

2) According to different uses and occasions, different impeller structures are adopted. Single and double channel impeller or double blade impeller with unique design can be adopted, which has good winding resistance, no blockage, strong processing ability and high efficiency and energy saving.

3) The worm chamber is usually a single worm type, with water absorption at the bottom, lateral drainage, and large flow area.

4) A replaceable wear-resistant sealing ring is installed between the impeller and the worm chamber to ensure the efficient operation of the pump.

5) For higher head pumps, the impeller is equipped with a back blade seal. Its function is to reduce the pressure of the liquid before the shaft seal of the pump chamber to balance the axial force, prevent impurity particles from entering the sealing device, and extend the service life of the seal.

6) The double-ended mechanical seal is installed between the motor and the pump head, for high powerSubmersible electric sewage pumpTwo single-ended mechanical seals can also be installed in series. The sealing material is tungsten carbide, silicon carbide, hard alloy pair, super wear-resistant sealing pair or graphite and other materials.

7) When the power is above 15kW, it is equipped with a self-contained cooling system. The back blade of the impeller makes the water in the worm chamber flow into the stator chamber for circulating cooling, which can ensure the normal operation of the water pump when the water level of the pool is low or it is released. There is also an oil-water probe in the wiring cavity. When the main cable or control cable is broken or leaked due to other reasons, the probe sends a signal and the control system protects the pump.

8) The oil chamber can be cooled and lubricated by mechanical seals. The motor cavity is partially isolated from the pump, and there is no electrode protection inside the oil-water probe. When the conveying medium enters the oil chamber, the electrode sends a signal, which is displayed by the control system to notify the management personnel to repair in time. At the same time, the control system closely monitors its leakage.

9) The lower end of the motor cavity is equipped with a water leakage detector-float switch, which sends a signal when the conveying medium enters the motor cavity, and the control system protects the pump.

10) The motor stator adopts F-class insulation (155.C). Built-in thermal overload protector, at the same time in the bearing installation also set thermal overload protector. It can prevent the motor from overheating and overload, bearing overtemperature, etc.

How to store, transport and anti-corrosion measures for high-lift deep well pumps For well pumps containing packed wooden boxes, they should be placed on a flat concrete floor. For deep well pumps without packed wooden boxes, they should be discharged flat on the pump rack with 3 support points. Both sides shall not be suspended in the air for more than 1m.

Luohe Huali Pump Industry Held "Fire Safety Knowledge Training" Activity

Luohe Huali Pump Co., Ltd. "fire safety knowledge training"

Luohe Huali Pump Industry Held "Welcome May Day" 3rd Staff Games

Opening Ceremony On April 30, 2019, Luohe Huali Pump Industry Co., Ltd. held the third employee sports meeting "Welcome May Day. Technical manager Shi Qiuyu presided over the opening ceremony, sales manager Zhu Qiuyue delivered an opening speech, and general manager Zhu Weili announced the opening of the games. The main purpose of holding this sports meeting is to enrich the cultural life of employees, enhance the interaction and communication between departments, further create a good working atmosphere of cohesion and unity, and cultivate the sense of competition, cooperation and fairness of the majority of cadres and employees. Put your physical fitness and good mental outlook into work. There are 7 ratios in this sports meeting.